Please visit our other sites at www.TriloBoats.com and TriloBoats.blogspot.com for plans, background and focused discussion.

16 October 2014

Amazing Grace? Yes and No

Bottom first, then Sides and a band overlapping the Chine.
Note the wrinkles low along the Bow Curve sides...
These remained manageably small.. no 'darting' was necessary.

Amazing Grace? Yes and No

Today was our 'coup de Grace'... we finished the installation of the Grace Ice and Water Shield underlayment for our copper plating.

Grace is a self-adhered, rubberized asphalt sheet material (comes in rolls of three foot width). A thin layer of plastic on its outer face protects the world from a sticky, gooey layer, which has the potential to fuse with plywood. This face has a peel-off layer of plasticized paper which must be removed before installation.

Our hope (mostly gratified) was that it would work well with the assemble, flip and join method we used to construct the Bottom.

Needless to say, the company nowhere suggests that Grace might be advisable for marine construction.
 

The Good News

When it sticks, it REALLY sticks. Especially to itself. 

Once well bonded, it's like skin on the hull. Overlaps adhere even better, with high confidence of water exclusion. It seems to thoroughly gasket fasteners... withdrawing occasional screws showed them to be coated entirely along their length!


The So-So News

Application is meticulous, demanding and slow. 

Any lapse of attention, or initial mis-alignment can result in a messy, wasteful sitchiAYshun. Still, we got through the whole thing with nothing worse than a little curl along an edge, here and there.

Peeling the paper was a challenge, at first. We took to scoring it at workable intervals to keep things manageable. 

Touching the warm, peeled sticky-side makes ya sympathize with Bre'r Rabbit. We did better by taking small folds of the paper - plasticized layer towards the Grace - and using them as grippers along the edge.


The Not So Good News

Adhesion doesn't appear fully consistent, even when temps are in the 70degF/ 20degC range. 

Initial grab drops to near nothing along with temps. In the 50degF / 10degC temps we're undergoing, we had to use a heat gun to achieve grab and bond.

Over-all handling is temperature dependant and awkwardly so. 

It's stiffer when cool, so is easy to handle, but doesn't like to grab or conform to the work. When warm, it goes limp in passive resistance... conforms well, but hard to deliver, and grabs at anything along the way.

There is a fringe of un-plastic-protected tar along each edge which caused problems. It's delicate, sticky, and once it curls back and touches itself, forget it. We finally took to trimming it off before starting.

Even simple cutting is difficult in warm weather, as it sticks to the knife and drags. Possibly, wetting in mineral spirits (a solvent which works well on the stuff) would help it slide along. If possible, plan your cutting in the cool of the day, morning or evening.

And it smells toxic... the box has ominous warnings to WEAR GLOVES and WASH YOUR HANDS. Warnings in ALL-CAPS tend to be worth heeding.


Sooooo...

We're basically happy with the results, at this point. But I'm not sure I'd use it again for this application (it's excellent for bedding hardware and between dead-wood). 

We're considering a last pass with a weed-burner, once the copper is on, warming it to hot-to-the-touch and whuppin' it all over with a mallet for good luck.

It was spendy and a lot of work, in retrospect.

In some ways, it wasn't much cleaner an operation than we could have managed with, say, a water emulsified asphalt, or even rubberized asphalt paint. Still, it didn't generate too much hard-to-dispose-of garbage (e.g., paint rollers, etc), and most of the off-cuts and remnants are still useful for other tasks.

Other alternatives we'd considered were tar (messy), elastomeric polyurethane paint (hard to find... 3M used to make some that we loved, but it's disappeared) and Irish felt (traditional and great to work with, but rare nowadays... what we found was prohibitively expensive to transport our way).


Grace is amazing. Time will tell if it has 'saved a wretch like we'.

2 comments:

  1. Full set of developed plans coming soon for the 32X8er? Interesting thought experiment to imagine that box loafing along in the tradewind belt. Looks yet again more refined than the Slacktide too. Looks HUGE in that from the bow pic. Inspirational and a fine contribution to marine architecture. Fair winds and best wishes from Mexico. BTWay: construction book coming soon also?

    ReplyDelete
    Replies
    1. Hi Bob,

      Hmm... fully developed plans are even further down the road than the DIY book. Sigh. The hours in a day are simply too few.

      The StudyPLANS for the T32x8 LUNA are essentially what we followed, with the exception that we raised the sheer to 4ft + 1ft (as opposed to 4ft + 8in, if memory serves). This allowed Anke full standing headroom throughout and increased enclosed volume, a bit.

      It does feel pretty big... we're coppering the bottom prior to lowering it to the ground, and when launched, it will lose another vertical foot. At that point, from the outside, it looks small and snug. Inside, it's pretty astounding how much room the box barge widens out, relative to LUNA (AS31), who had the same layout.

      For example, Luna's forward bunk area is 6ft wide at its (aft) head, and 4ft at the (fwd) foot. The barge is 8ft x 8ft. LUNA has one leanbank/storage area to port, tapering to a fwd point, leaving 5ft tapering to 4ft for the bunk, itself. The barge has TWO leanbanks, P&S, leaving 6ft for the entire length of the bunk.

      George Beuhler praised 'little big boats' over 'big little boats', referring to a spacious interior/deck feel on a small footprint. LUNA is an improvement, I feel, over most boats her size, in this regard, and the barge even moreso.

      Fair winds and best wishes back atcha!

      Dave Z

      Delete

About Me

My photo
Anke and I live aboard WAYWARD, our T32x8 ketch. We sail by wind, tide and muscle in the waters of mid- to northern Southeast Alaska. We try to maximize the joys of life, and minimize the chores. ........ We live between the communities of SE Alaska, but drop in to visit with friends. ........ We're working toward a subsistence lifestyle, somewhat impeded by addictions to coffee, chocolate and cheese. ........ We think TEOTWAWKI is looming, and while we won't be ready, we'd at least like comfortable seats. Our personal TEOTWAWKI is definitely approaching in the guise of older age. We're prepping our fleet and assets in the face of one or more decades of declining abilities, aiming to live happily on or very near the water until the end!